Fiber Laser for Beginners: What Metal Engraving Actually Requires
How this guide was made: researched from manufacturer specifications, current retailer listings, and owner reports — not hands-on lab testing. Prices are typical U.S. ranges as of November 2026 and move with sales. When a machine gets real hours in our own shop, this page gets updated and says so. See our disclosure.
Every beginner hits the same wall: the diode or CO2 laser that cuts wood and acrylic beautifully leaves almost nothing on bare stainless, brass, or aluminum. That is not a power problem — it is a wavelength problem. Metal engraving requires a fiber laser, a 1064 nm source metals absorb, plus a few things product pages underplay: the right field lens, real eye and fume safety for an open galvo machine, and software you can live with.
Why bare metal needs 1064 nm
A blue diode emits around 455 nm and a CO2 tube around 10,600 nm; polished metal reflects most of both. A fiber source emits 1064 nm, which stainless, carbon steel, aluminum, brass, copper, and titanium absorb well enough to mark directly — no coating, no spray. That is why a 20W fiber can write a crisp logo into bare stainless while a much more powerful diode leaves a faint streak.
There are workarounds, and beginners should know their limits. Anodized aluminum engraves on diode and CO2 because the beam burns the dyed coating, not the metal. Marking sprays let a diode or CO2 bond a dark mark onto bare metal, at a per-can cost and an extra spray-wash step. An infrared (IR) module added to a diode machine — the xTool S1 route covered in our S1 vs P2S comparison — marks bare metal at 1064 nm too, but slower and shallower than a dedicated fiber. Occasional dog tags? A workaround is fine. A product line of bare-metal goods? That is fiber territory.
Mark, engrave, or cut — three different promises
- Marking changes the surface color or texture without meaningful depth: black marks, annealed colors, serial numbers, QR codes. Every fiber machine here does this fast.
- Deep engraving removes material — the recessed lettering on a coin, knife, or firearm part. This is where wattage and time matter; more power means fewer passes.
- Cutting thin metal is possible on higher-power fiber — xTool lists the 60W MOPA F2 Ultra cutting stainless and brass up to about 2 mm — but it is slow, edge quality varies, and it is not a substitute for a metal-cutting shop tool. Buy a fiber to mark and engrave; treat thin cutting as a bonus.
The beginner machines, side by side
| Route | What it is | Typical price, Nov 2026 |
|---|---|---|
| Diode + IR module (e.g. xTool S1 with IR) | 1064 nm add-on head on a gantry diode; marks metal, still cuts wood | Typically $1,700–$2,300 with the IR module, as of November 2026 |
| Entry galvo fiber, 20–30W (OMTech Galvo class, ComMarker B4 class) | Standard fiber, monochrome marks, EZCAD or LightBurn Galvo, open frame | Typically $1,400–$2,000, as of November 2026 |
| Galvo fiber, 50W (OMTech Galvo class) | Faster deep engraving, more headroom for production marking | Typically $2,700–$3,300, as of November 2026 |
| MOPA fiber, 30W class (OMTech MOPA class) | Adjustable pulse width; color marking on stainless, finer control | Typically $2,400–$2,900, as of November 2026 |
| xTool F1 Ultra | Enclosed 20W fiber + 20W diode, cameras, conveyor-ready, beginner software | Typically $3,000–$3,600, as of November 2026 |
| xTool F2 Ultra | Enclosed 60W MOPA fiber (Single) or plus 40W diode (Dual), dual 48MP cameras, 220 × 220 mm field, up to 15,000 mm/s listed | Typically $4,300–$5,300, as of November 2026 |
Standard fiber vs MOPA: do you need color?
A standard fiber laser marks in monochrome — blacks, grays, and whites — and costs the least. A MOPA fiber adds adjustable pulse width and frequency. Owners buy MOPA for two reasons: genuine color marking on stainless steel and titanium (xTool claims 100+ colors for the F2 Ultra; results are angle- and finish-dependent in owner reports), and cleaner black marking on anodized aluminum and some plastics. If your products are logos, text, serials, and black marks, standard fiber does the job for roughly half the money. If color-on-steel jewelry, knives, or tumblers are the product, MOPA is the requirement — not an upgrade.
Power: 20W, 30W, 50W, or 60W?
For surface marking, 20–30W is enough for nearly every beginner project, and owners of 30W machines run real small businesses on them. Higher wattage buys speed and depth, not new materials: a 50–60W source deep-engraves faster, cuts thin metal more plausibly, and finishes batch marking sooner. It does not make the work area bigger, and it does not turn wood into a fiber material — fiber is poor on wood, leather, and clear acrylic, which is why dual-laser machines pair it with a diode, and why many shops keep their CO2 or diode for organics. See our Etsy sellers roundup for how the types divide product lines.
Galvo reality: speed, field size, and focus
Most fiber machines are galvo machines: two small mirrors steer the beam, so marking speeds are listed in the thousands of mm/s — 7,000–10,000 mm/s on OMTech Galvo models, up to 15,000 mm/s on the F2 Ultra. The trade-off is the field. The lens defines a fixed square — commonly 110 × 110 mm, 150 × 150 mm, 175 × 175 mm, or 200 × 200 mm, and 220 × 220 mm on the F2 Ultra. A bigger lens covers a bigger blank but spreads the energy and softens fine detail and depth; a smaller lens is sharper and deeper on small work. There is no gantry to extend later, and tall or curved parts need focus headroom or a rotary — sold separately on most machines — for rings, tumblers, and tools. Flat, small, repeatable parts are what fiber does best.
Software: the daily-driver decision
Traditional galvo machines run EZCAD (often EZCAD2, Windows-only, powerful but dated) or LightBurn's Galvo edition, which most established shops prefer and which our laser software comparison covers in depth. The enclosed xTool fiber machines run xTool Studio instead — free, camera-driven, and far easier for a beginner, but not LightBurn-compatible on the F2 Ultra per xTool's current documentation. Decide before you buy: a LightBurn workflow you already own points to OMTech/ComMarker-class galvos; a first laser with no workflow points to the enclosed xTool route.
Safety: the part beginners under-budget
- Enclosed vs open: the F1 Ultra and F2 Ultra are enclosed desktop machines. Most entry galvos are open-frame Class 4 devices — the beam and reflections are an eye hazard to everyone in the room.
- Eye protection: if the machine is open, everyone present needs eyewear rated for 1064 nm (check the OD rating), not generic laser glasses. Budget for it.
- Fumes: engraving metal and especially plastics produces fine particulate and fumes. Vent outside or use a proper purifier; an enclosure alone is not extraction.
- Fire and material rules: never leave a running laser unattended, and check any plastic or coated blank before lasering it — some coatings and plastics produce hazardous fumes under any laser type.
True cost of ownership
- The machine is most of it: fiber sources are manufacturer-rated for very long service life (OMTech lists an estimated 100,000-hour MTTF on its Galvo line) and have no CO2-style tube or chiller consumables — a real running-cost advantage.
- The extras that actually matter: a rotary for round work, a second field lens if you split time between tiny and large blanks, 1064 nm eyewear for open machines, and extraction.
- Software: EZCAD is typically bundled; LightBurn Galvo is a separate paid license; xTool Studio is free.
- Blanks: stainless tags, challenge-coin blanks, and business-card stock are cheap per piece — the business case in our startup guide (machine cost recovered over units sold) applies even more strongly at fiber marking speeds.
The verdict
Start with a 30W-class galvo fiber if bare-metal marking is a real product line — tags, tools, knives, jewelry, industrial ID — and you are comfortable with an open machine, proper eyewear, and EZCAD or LightBurn Galvo. Typically $1,400–$2,000 as of November 2026, it is the cheapest honest entry to real metal work.
Choose MOPA if color on stainless or titanium, or clean black marks on anodized aluminum, are the products customers will pay for. Expect typically $2,400–$2,900 for a 30W MOPA galvo, or step up to the enclosed F2 Ultra class at typically $4,300–$5,300.
Choose the enclosed xTool F1 Ultra or F2 Ultra if beginners, employees, or a shared space will use the machine, camera placement matters, or you also want diode work in the same footprint. You pay for the enclosure, cameras, and software ease — not for a different wavelength.
Skip fiber for now if metal is an occasional logo on a coated tumbler. A diode you already own, an IR add-on, or marking spray covers that for far less, and the fiber money is better spent on the materials your current machine already sells.
Official product pages / resources
Check specs and current pricing straight from the manufacturers (prices change constantly):
- xTool — F2 Ultra, F1 Ultra, and the S1 with its infrared module; check each product page for current Single/Dual configuration pricing
- OMTech — Galvo fiber and MOPA fiber markers in 20W–60W classes; check each product page for lens, rotary, and software inclusions
- ComMarker — B4 and B6 fiber and MOPA markers; check current field-lens and LightBurn support details on each product page
- LightBurn — Galvo edition software for supported fiber machines; check the supported-device list for your exact model before buying
Our design files live in TheUnrulyMaker shop on Etsy; the physical finds — tools, parts, and liquidation gear — are in our eBay store, Easy401K Liquidations.